
A substation is the junction box of the power system: it changes voltage, switches circuits in and out, measures power and protects equipment from faults. The way its busbars and circuit breakers are arranged decides how reliable the supply is and how easily equipment can be maintained. “Types of substation”, “equipment in a substation”, “breaker-and-a-half scheme” and “purpose of a bus coupler” are frequent questions in PGCB, BPDB, BREB, DPDC, DESCO, BCS (EEE) and polytechnic exams. This post covers them with an animated single-line diagram, a busbar-fault animation, comparison tables, solved problems and MCQs.
- A substation transforms voltage, switches, measures and protects. It does not generate power.
- Bangladesh levels: 400/230/132 kV transmission (PGCB) and 33/11/0.4 kV distribution (BPDB, BREB, DPDC, DESCO, NESCO, WZPDCL).
- Main equipment: lightning arrester, isolator, earth switch, CT, PT/CVT, circuit breaker, busbar, power transformer, relays, battery bank and earthing grid.
- Isolators are off-load devices: open the breaker first, then the isolator; close the isolator first, then the breaker.
- Busbar schemes in rising reliability and cost: single → sectionalised → main & transfer → double bus → breaker-and-a-half / double breaker; the ring bus uses only one breaker per circuit.
- Busbars are protected by busbar differential protection (Kirchhoff’s current law: currents into a healthy bus sum to zero).
1. What Is a Substation?
A substation is an assembly of equipment where electrical energy is received at one voltage and sent out at the same or a different voltage, under control and protection. Power is generated at about 11–21 kV, stepped up for long-distance transmission (400/230/132 kV), then stepped down in stages (33 kV → 11 kV → 0.4 kV) until it reaches consumers at 400/230 V. Every step happens in a substation.
The main functions of a substation are:
- Voltage transformation (step-up or step-down) with power transformers.
- Switching: connecting and disconnecting lines, transformers and feeders for operation and maintenance.
- Protection: detecting faults with CTs, PTs and relays and tripping circuit breakers.
- Measurement and control: energy metering, SCADA, voltage control with on-load tap changers (OLTC) and reactive power control with capacitor banks or reactors.
2. Types of Substation
| Basis | Types | Notes |
|---|---|---|
| Function / service | Step-up (generating), grid / transmission, sub-transmission, distribution, switching, converter | A switching substation has no transformer; a converter station changes AC ↔ DC (e.g. the back-to-back HVDC station at Bheramara for the Bangladesh–India interconnection). |
| Operating voltage | HV (up to 66 kV), EHV (132–400 kV), UHV (above 765 kV) | Classification limits differ slightly between textbooks. |
| Construction | Outdoor air-insulated (AIS), indoor, gas-insulated (GIS), pole-mounted, compact / package, mobile | GIS uses SF6-filled metal enclosures and needs only about 10–25 % of the land of an AIS, so it suits cities such as Dhaka. |
| Importance | Grid, town, industrial | Industrial substations feed a single large consumer. |
AIS vs GIS: AIS is cheaper and easy to inspect but needs large land and is exposed to pollution and weather. GIS is compact, very reliable and almost maintenance-free, but costs more and needs careful SF6 handling because SF6 is a strong greenhouse gas.
3. Single-Line Diagram and Equipment
A single-line diagram (SLD) shows a three-phase system with one line per circuit and standard symbols. The animation below follows power through a typical 132/33 kV grid substation.
| Equipment | Function |
|---|---|
| Lightning arrester (LA) | Diverts lightning and switching surges to earth; installed at the line entry and near the transformer. |
| Isolator (disconnector) | Gives a visible open point for safe maintenance; operated only on no load. |
| Earth switch | Connects an isolated line to earth to discharge trapped charge before work starts. |
| Current transformer (CT) | Steps current down (e.g. 800/1 A) for relays and meters. |
| Potential transformer (PT) / CVT | Steps voltage down to 110 V for relays and meters; a CVT can also couple PLCC signals. |
| Circuit breaker (CB) | Makes and breaks normal and fault current; SF6 at 132 kV and above, vacuum (VCB) at 33/11 kV. |
| Busbar | Common conductor connecting incoming and outgoing circuits (aluminium tube or strung ACSR outdoors, copper/aluminium bars indoors). |
| Power transformer | Changes voltage level; has OLTC, Buchholz relay, oil/winding temperature indicators and differential protection. |
| Wave trap (line trap) | Blocks high-frequency PLCC signals from entering the bus while passing 50 Hz power. |
| Capacitor bank / shunt reactor | Supplies or absorbs reactive power to control voltage and power factor. |
| Relay and control panels, SCADA | Detect faults, send trip commands, display and record data, allow remote control. |
| Battery bank and charger | Provides reliable DC (commonly 110 V or 220 V) for tripping and control even when AC is lost. |
| Station service transformer | Supplies the substation’s own lighting, cooling fans and pumps. |
| Earthing grid | Keeps step and touch voltages safe and provides a low-resistance path for fault current. |
4. Switching Sequence and Interlocking
An isolator has no arc-quenching ability, so it must never make or break load current. The rule is:
To de-energise: open CB → open isolators → close earth switch. To energise: open earth switch → close isolators → close CB.Electrical and mechanical interlocks enforce this order: an isolator cannot operate while its breaker is closed, and an earth switch cannot close while the isolator is closed.
5. Busbar Arrangements
The busbar arrangement is chosen by balancing reliability, flexibility for maintenance, cost and space. The animation compares the simplest scheme with a double-bus scheme when a bus fault occurs.
5.1 Single busbar
All incoming and outgoing circuits connect to one bus. It is the simplest and cheapest arrangement and easy to operate. However, a bus fault or bus maintenance shuts down the whole substation, and maintaining a feeder breaker disconnects that feeder. It is used in small 11 kV and 0.4 kV substations.
5.2 Sectionalised single busbar
The bus is split into two or more sections joined by a bus-section breaker (sectionaliser). A fault on one section trips only that section, so half the load stays in service, and each section can be maintained separately. Sources and loads are divided between the sections. This scheme is common in 33/11 kV distribution substations.
5.3 Main and transfer bus
A second, normally dead transfer bus is added, with a transfer (bus-coupler) breaker. When a feeder breaker needs maintenance, that feeder is moved to the transfer bus and protected by the transfer breaker, without interrupting the feeder. A fault on the main bus still shuts down everything. The scheme is widely used at 132 kV and 33 kV.
5.4 Double busbar, single breaker (with bus coupler)
There are two main buses. Each circuit has one breaker and can be connected to either bus through two bus-selector isolators. A bus coupler breaker joins the buses. Either bus can be maintained or cleared of a fault while all circuits run on the other one, and circuits can be split between the buses to limit fault level. Maintaining a circuit breaker still needs an outage of that circuit unless a bypass is provided. It is common at 132 kV and 230 kV.
5.5 Double busbar, double breaker
Each circuit has two breakers, one to each bus. Any breaker or either bus can be taken out without interrupting any circuit, so reliability is very high. The cost is also the highest (2 breakers per circuit), so it is used only for very important circuits such as large generator connections.
5.6 Breaker-and-a-half (one-and-a-half breaker)
Two buses are connected by “diameters” of three breakers in series, with two circuits taken from the points between them. That is 3 breakers for 2 circuits, or 1.5 breakers per circuit. Any breaker can be maintained without an outage, and a fault on either bus is cleared without losing any circuit. It is the standard choice for 400 kV and other EHV substations.
5.7 Ring (mesh) bus
Breakers form a closed ring and each circuit connects between two breakers, so there is one breaker per circuit. Any breaker can be maintained without an outage, and there is no single main bus to fail. However, when the ring is open for maintenance, a second fault can split the substation, the protection is more complex and the ring is hard to expand. It suits substations with about four to six circuits.
6. Comparison of Busbar Schemes
| Scheme | CBs per circuit | Bus fault effect | CB maintenance without outage? | Cost | Typical use |
|---|---|---|---|---|---|
| Single bus | 1 | Total shutdown | No | Lowest | Small 11 kV / 0.4 kV |
| Sectionalised single bus | 1 (+ bus section CB) | Only faulty section lost | No | Low | 33/11 kV distribution |
| Main & transfer | 1 (+ transfer CB) | Total shutdown | Yes (one at a time) | Moderate | 132 kV, 33 kV |
| Double bus, single breaker | 1 (+ bus coupler) | Circuits moved to healthy bus | No (unless bypass) | Moderate–high | 132 / 230 kV grid |
| Double bus, double breaker | 2 | No circuit lost | Yes | Highest | Major generating stations |
| Breaker-and-a-half | 1.5 | No circuit lost | Yes | High | 400 kV / EHV |
| Ring (mesh) | 1 | No main bus | Yes (ring opens) | Moderate | 4–6 circuit stations |
Exam tip: “Which scheme needs 1.5 breakers per circuit?” → breaker-and-a-half. “Which scheme lets a feeder breaker be maintained without interrupting the feeder, using an extra bus?” → main and transfer bus. “Which device connects two buses?” → bus coupler.
7. Busbar Protection and Earthing
Busbar differential protection compares all currents entering and leaving the bus. For a healthy bus or an external fault, Kirchhoff’s current law gives ΣI = 0 and the relay stays stable. For an internal bus fault the currents no longer balance and the relay trips every breaker connected to that bus (or that bus zone). Common forms are high-impedance circulating-current (Merz–Price type) and low-impedance numerical schemes. Because a bus fault carries a very high current and affects many circuits, busbar protection must be fast and very stable against CT saturation during external faults. Breaker-failure protection backs it up by tripping the adjacent breakers if a breaker fails to open.
Substation earthing: a buried mesh of copper or galvanised steel conductors with earth rods connects all equipment frames, neutrals, arresters and fences. Its purposes are to:
- keep step voltage (between the feet) and touch voltage (between hand and feet) within safe limits during a fault;
- provide a low-resistance path so protective relays operate reliably;
- discharge lightning surges.
Large transmission substations aim for an earth resistance of about 1 Ω or lower; a crushed-rock (gravel) surface layer increases the contact resistance of a person’s feet and improves safety.
8. Solved Problems
Problem 1. A 400 kV substation has 8 circuits (lines and transformers). How many circuit breakers are needed for (a) breaker-and-a-half, (b) double bus double breaker, (c) ring bus?
Solution: (a) 8 × 1.5 = 12 breakers (4 diameters × 3). (b) 8 × 2 = 16 breakers. (c) 8 breakers (one per circuit).
Problem 2. A 132 kV breaker is rated at 31.5 kA symmetrical breaking current. Find its breaking capacity in MVA.
S = √3 × V × I = √3 × 132 kV × 31.5 kA ≈ 7,200 MVAProblem 3. Find the full-load currents of a 50 MVA, 132/33 kV transformer.
IHV = 50 × 10⁶ / (√3 × 132 × 10³) ≈ 219 A, ILV = 50 × 10⁶ / (√3 × 33 × 10³) ≈ 875 AThis is why CTs on the 33 kV side need a higher primary rating (e.g. 1000/1 A) than those on the 132 kV side (e.g. 300/1 A).
9. Practice MCQs
1. An isolator is operated: (a) On full load (b) On no load (c) During a fault (d) Any time
2. The correct sequence to de-energise a feeder is: (a) Isolator then CB (b) CB then isolator (c) Both together (d) Earth switch first
3. The breaker-and-a-half scheme uses how many breakers per circuit? (a) 1 (b) 1.5 (c) 2 (d) 3
4. A bus coupler is used to: (a) Step down voltage (b) Connect two busbars (c) Measure current (d) Suppress surges
5. The cheapest but least reliable busbar arrangement is: (a) Ring (b) Double bus (c) Single bus (d) Breaker-and-a-half
6. Which equipment protects a substation from lightning surges? (a) Isolator (b) CT (c) Lightning arrester (d) Wave trap
7. A wave trap in a substation is used for: (a) Lightning protection (b) PLCC carrier communication (c) Reactive power control (d) Earthing
8. The main advantage of GIS over AIS is: (a) Lower cost (b) Much smaller space (c) No SF6 needed (d) Easier visual inspection
9. Busbar differential protection is based on: (a) Ohm’s law (b) Kirchhoff’s current law (c) Lenz’s law (d) Faraday’s law
10. Which substation has no power transformer? (a) Step-up (b) Distribution (c) Switching (d) Grid
10. বাংলায় দ্রুত রিভিশন
- সাবস্টেশন: ভোল্টেজ পরিবর্তন, সুইচিং, পরিমাপ ও প্রোটেকশনের স্থান; এখানে বিদ্যুৎ উৎপাদন হয় না।
- বাংলাদেশে ট্রান্সমিশন (PGCB): ৪০০/২৩০/১৩২ kV; বিতরণ: ৩৩/১১/০.৪ kV।
- আইসোলেটর নো-লোডে চালাতে হয়। বন্ধ করার সময় আগে CB, পরে আইসোলেটর; চালুর সময় আগে আইসোলেটর, পরে CB।
- সিঙ্গেল বাস সবচেয়ে সস্তা কিন্তু কম নির্ভরযোগ্য; বাস ফল্টে পুরো সাবস্টেশন বন্ধ।
- বাস কাপলার দুটি বাসবারকে যুক্ত করে; ডাবল বাসে এক বাস ফল্ট হলে সব সার্কিট অন্য বাসে নেওয়া যায়।
- ব্রেকার-অ্যান্ড-এ-হাফ: ২টি সার্কিটের জন্য ৩টি ব্রেকার (প্রতি সার্কিটে ১.৫টি); ৪০০ kV সাবস্টেশনে ব্যবহৃত।
- বাসবার প্রোটেকশন: ডিফারেনশিয়াল (KCL); আর্থিং গ্রিড স্টেপ ও টাচ ভোল্টেজ নিরাপদ রাখে।
- GIS জায়গা কম লাগে (SF6 গ্যাস), AIS সস্তা কিন্তু বেশি জায়গা লাগে।
Related Posts
- BREB/PBS Job Exam Preparation
- Bangladesh Power Sector MCQs for Job Exams
- Departmental Job Preparation for EEE
- Mastering Your EEE Job Viva Voce
- Equivalent Circuit of a Transmission Line
References: V. K. Mehta & Rohit Mehta, Principles of Power System; J. B. Gupta, Switchgear and Protection; IEEE Std 80, Guide for Safety in AC Substation Grounding. Images and animations: original work by Totalecer.
Thank you for visiting my blog.